PhonePhone No: 02082209986

WhatsAppWhatsapp: 447811247454

Wheel Balancer Buying Guide UK: What to Look For

Wheel Balancer Buying Guide UK: What to Look For

Short answer: a good wheel balancer for a home garage or small tyre business should be accurate to within a gram or two, take the largest wheels you fit, and check and calibrate itself so you can trust every reading. Our computerised BLS-WB100 wheel balancer is accurate to +-1g, takes rims from 10 to 24 inch and wheels up to 70kg, runs a fully automatic balance check, calibrates itself and comes with a protection hood. It costs £749 delivered to mainland England and Wales.

Why every wheel needs balancing

No tyre and no rim is perfectly even. The valve, the join in the tyre carcass and small differences in rubber thickness all add a few grams in one spot. At walking speed you would never notice. At motorway speed a wheel turns many times a second, and a few grams on one side become a force that pulls the wheel up and down and side to side. That is the vibration drivers feel through the steering wheel or the seat, very often around 60 mph.

Each time a tyre is fitted, swapped or repaired, the balance of the wheel changes. That is why tyre fitting and balancing always go together. An unbalanced wheel is not only uncomfortable: it wears tyres unevenly and puts extra load on wheel bearings, track rod ends and dampers over time.

There are two kinds of imbalance. Static imbalance is a heavy spot that makes the wheel hop up and down. Dynamic imbalance is a heavy spot on one side of the rim more than the other, which makes the wheel wobble from side to side. A computerised balancer measures both and tells you how much weight to add on the inner and outer edge of the rim, and where.

Reading the symptoms

Before you blame balance, match the symptom to the likely cause. Balancing is the cheapest fix, but it does not cure everything.

Symptom Most likely cause What to do
Steering wheel shakes at around 50 to 70 mph Front wheel out of balance Balance both front wheels, check for a lost weight
Seat or floor vibrates, steering is calm Rear wheel out of balance Balance both rear wheels
Vibration at all speeds, gets worse with speed Bent rim, tyre fault or worn parts Check runout and suspension, balancing alone will not fix it
Vibration only when braking Brake discs, not balance Inspect discs and pads
Patchy, cupped tyre wear Long-term imbalance or worn dampers Balance, then check dampers and alignment

How a computerised wheel balancer works

  1. Mount the wheel. The wheel is clamped on the shaft through its centre bore, using a cone that fits the hole snugly.
  2. Enter the rim data. The machine needs to know where the rim is and how wide and big it is, so it can work out where the weights go. The manual shows how the BLS-WB100 takes these measurements.
  3. Close the hood and spin. The shaft spins the wheel and sensors measure the forces from the heavy spots.
  4. Read the result. The display shows how many grams to add on the inner and outer plane, and the machine guides you to the right position on the rim.
  5. Fit the weights and check. Clip-on or stick-on weights go on at the marked spots. A second spin should show zero, or close to it, on both sides.

On the BLS-WB100 the most important part, the balance check itself, is fully automatic. High precision bearings keep the noise down and the readings stable, and self-calibration means you are not relying on guesswork to keep it accurate.

What to look for when you buy a wheel balancer

  • Accuracy. This is the whole point of the machine. If it is out by several grams, you will still get vibration at speed. The BLS-WB100 is accurate to +-1g.
  • Wheel diameter. Check the biggest wheels you will see. SUVs and performance cars now often run 20 inch rims and above. The BLS-WB100 takes up to 24 inch.
  • Wheel weight. Large SUV and van wheels with tyres are heavy. The BLS-WB100 is rated for wheels up to 70kg.
  • Calibration. A balancer that calibrates itself stays accurate with less effort from you. Cheap manual machines drift.
  • Protection hood. A spinning wheel throws off mud, water and small stones. The hood is included with the BLS-WB100 and should always be down when the wheel spins.
  • Ease of use. A good balancer should be quick enough for a busy Saturday and simple enough for a new member of staff or a home user.
  • Manual and support. You should be able to read the user manual before you buy. The manual for the BLS-WB100 is on the product page.
  • Spare parts and service. Buy from a supplier who will still answer the phone after the sale.

BLS-WB100 at a glance

Feature BLS-WB100
Model BLS-WB100 computerised wheel balancer
Balancing accuracy +-1g
Maximum wheel diameter 24 inch
Maximum wheel weight 70kg
Balance check Fully automatic
Calibration Self-calibration
Protection hood Included
Price £749 delivered (England and Wales)

Product page and manual: computerised wheel balancer BLS-WB100. You can also browse the wheel balancer collection. For anything not listed above, such as the power supply, the cones supplied and the floor fixing, check the user manual or ask us before ordering.

Getting a good result every time

Most balancing problems come from the preparation, not from the machine. A routine our customers find works well:

  1. Clean the wheel. Mud on the inside of the rim, stones in the tread and old tyre sealant all change the reading.
  2. Remove old weights. Start from zero, especially on a new tyre.
  3. Set the tyre pressure to the normal running pressure, and check the tyre is seated evenly on the rim.
  4. Use the right cone and clamp the wheel firmly. A wheel that is not centred will never balance properly.
  5. Enter the rim data carefully and pick the right weight type: clip-on for steel and many alloy rims, stick-on where clip-on weights would mark the face of the alloy.
  6. Spin, fit, re-spin. Always check after fitting the weights. If the second spin is still out, look at the cone and the clamp before adding more weight.

If a wheel needs a lot of weight, or keeps coming back out after balancing, the problem may be the tyre or the rim. Rotating the tyre on the rim on the tyre changer can sometimes cancel out a heavy spot so that much less weight is needed.

Who the BLS-WB100 suits

  • Home mechanics who change their own summer and winter tyres or run track day wheels and are tired of paying for balancing each time.
  • Small garages that already do servicing and want to add tyres as a second service.
  • New tyre businesses setting up their first bay on a sensible budget.

To see whether it pays back, take the number of wheels you balance in a typical month and what you charge or pay per wheel. For example, if you charge £10 a wheel, 75 wheels covers the £749 price. Use your own local figures, but for a garage that fits tyres every day the sums usually come out quickly.

The rest of the tyre bay

A balancer on its own only does half the job. You also need to get the tyre on and off the rim, air to seat and inflate it, and a way to get the wheels off the car.

Machine Job Price
Fully automatic tyre changer Removes and fits tyres, seven pedals control the turntable, tower and jaws £1,799
Computerised wheel balancer BLS-WB100 Balances the wheel after fitting, +-1g £749
200L air compressor Air for the tyre changer, inflating and air tools, 13 CFM at 115 PSI £750
Changer, balancer and compressor together Complete tyre fitting set £3,298

For a deep look at the other big machine, read the tyre changer buying guide. How the whole set fits into a small garage, including lifting the car, is covered in tyre changer and wheel balancer for a small garage.

Paying for it: buy online with card, Apple Pay, Shop Pay or Klarna (pay in 3 interest-free payments or spread the cost), or order by phone or WhatsApp and pay the driver on delivery by card, bank transfer or cash. See payment terms.

Setting up the balancer

  • Floor. Stand it on a flat, solid floor. A balancer that rocks gives poor readings. Check the manual for whether it should be fixed down.
  • Space. Leave room in front to lift wheels on and off, and room for the hood to open fully.
  • Light. Good light over the machine makes weight positions easy to see.
  • Power. Check the supply in the manual and tell us what you have in the garage if you are unsure.
  • Near the changer. Put the balancer a step or two from the tyre changer so the wheel moves straight from one to the other.

Delivery is by our own vans from Purfleet, Essex. Scotland is £100 extra, and we do not deliver to Ireland, but your courier can collect. More on our delivery page.

Questions and answers

How accurate should a wheel balancer be?

Within a gram or two. Our BLS-WB100 is accurate to +-1g, which is what you want to avoid vibration at motorway speed.

Why does my car vibrate at 60 mph after new tyres?

Most often a wheel is out of balance or a weight has come off. Steering shake points to the front wheels, seat vibration to the rear. If balancing does not fix it, check the rims, tyres and suspension.

Can I balance wheels at home?

Yes. A computerised balancer like the BLS-WB100 is simple enough for home use. You need a flat floor, a power supply and some room around it.

How much is a wheel balancer in the UK?

Our computerised BLS-WB100 wheel balancer is £749 delivered to mainland England and Wales. Scotland is £100 extra.

What size wheels can the BLS-WB100 balance?

Wheels up to 24 inch in diameter and up to 70kg in weight.

Not sure which lift fits? Call us on 020 8220 9986 or message us on WhatsApp 07811 247454, every day 9am to 9pm. Send your ceiling height, floor and the cars you work on, and we will tell you which lift fits.


Get a price for your garage

Leave your number and postcode. We call you back with a delivered or installed price and check the lift fits your ceiling and floor. Every day 9am to 9pm.

Delivered and installed by our own team. Pay online, with Klarna or on delivery. We only use your details to answer this request.