PhonePhone No: 02082209986

WhatsAppWhatsapp: 447811247454

Car Lift Maintenance Guide: Chains, Cables, Hydraulic Oil, Locks and a Simple Schedule

Car Lift Maintenance Guide: Chains, Cables, Hydraulic Oil, Locks and a Simple Schedule

Short answer: car lift maintenance is mostly a few minutes of looking and a few minutes with an oil can. Check the lift before each day’s use, keep chains, cables, pulleys and lock mechanisms clean and lubricated, check the hydraulic oil level and hoses, test that every lock engages, and check the anchor bolts and concrete now and then. The manual for our 4000kg 2 Post Lift puts it simply: check the lift at the beginning of every shift, lubricate the chain and check the hydraulic fluid. Exact intervals, lubricants and oil grades are in the manual for your model, and the manual always wins over any general guide, including this one.

What actually wears on a car lift

A lift has very few moving parts compared with the cars it lifts, but the parts it has carry tonnes over your head. These are the ones that need attention:

  • Chains and cables. They carry or synchronise the load. Chains stretch and stiffen without lubrication, cables fray and corrode.
  • Pulleys (sheaves) and their pins. A dry or worn pulley wears the chain or cable running over it.
  • Hydraulic system. Seals, hoses, fittings and the oil itself. Low or dirty oil makes the lift slow, jerky or noisy.
  • Safety locks. Pawls, springs and release linkages. Dirt and dried grease stop them dropping in cleanly.
  • Arms, pins and pads. Arm pivot pins, arm restraints and rubber pads take a knock every lift.
  • Anchors and floor. Bolts can work loose and concrete can crack around them, especially in the first months after installation.

Know your lift: what each design needs

Different drive systems need slightly different attention. This is what the product listings tell us about each of our lifts and where to focus:

Lift Drive and locks Where to focus
4000kg 2 Post Electro-hydraulic, equalised cables Check at the start of every shift, lubricate the chain, check hydraulic fluid (from the product listing)
6 Ton 2 Post Floor plate chain drive Chains under the floor plate: lift the plate to inspect and lubricate
5000kg 2 Post Double cylinder, hidden oil pipes and cables Hoses and cables are inside the posts: look for oil at the cylinders and fittings
5 Ton Electro Locks 2 Post Double cylinder, electro solenoid locks Locks release electrically: check they engage evenly and the wiring is undamaged
4000kg 4 Post Hydraulic cylinder, leaf chains linking all four posts Chains and the single lock release linkage
5500kg 4 Post Alignment Cables, locks linked by control rods Cables for wear, rods and linkages so all four locks engage together
Scissor lifts Hydraulic, mechanical lock Pivot pins, hoses where they flex, the mechanical lock

The user manual for each lift is linked on its product page. Download it now and keep a printed copy by the lift, because the oil grade, lubricant and torque figures you need are in it.

Chains and cables

  • Clean before you lubricate. Wipe off grit and old dried lubricant first. New oil on top of grit makes grinding paste.
  • Use the lubricant the manual names. A thin, penetrating chain lubricant reaches between the links. Thick grease on the outside of a chain mostly collects dirt.
  • Look for stiff links. Run the lift up and down and watch where the chain bends over its pulley. A link that stays kinked needs attention.
  • Check cables for broken strands, kinks, flattening and rust, especially where they run over pulleys and at the end fittings. A damaged cable is replaced, not repaired.
  • Check synchronisation. On a 2 post lift both carriages should lock at the same height. If one side clicks noticeably later, the equalising cables may need adjusting as the manual describes.

On a floor plate lift the chains or hoses run under the plate between the posts. Lift the plate when you do this check and refit it properly afterwards. More on that layout in floor plate vs clear floor 2 post lifts.

Hydraulic oil and hoses

  1. Check the level with the lift fully lowered. With the lift up, oil sits in the cylinders and the tank reads low.
  2. Top up only with the grade in the manual. Do not mix oil types. If you are not sure what is in there, ask us before adding anything.
  3. Look at the oil. Clean oil is clear. Milky oil means water has got in, dark or gritty oil means it is overdue for a change.
  4. Check hoses where they move or bend, and every fitting for weeping. Hoses that rub on a post or under a plate wear through.
  5. Watch for a slow sink. A lift that creeps down on the hydraulics points to a seal or valve problem. It is one more reason never to work under a car that is not on the locks.

Safety locks

The locks are what you trust when you are underneath, so give them the most attention. Raise the empty lift and listen: each lock should drop in with a clean, even click on every post. Clean the lock pawls and the lock ladders, lubricate the pivot as the manual says, and check that springs pull the pawls back firmly. On a 4 post lift with a single release handle, check that all four locks engage and release together. On electro solenoid locks, check they engage evenly and that cables to the solenoids are not chafed.

Anchors, base plates and the floor

Check the anchor bolts after the first few weeks of use, then every few months. The tightening torque is in the manual. Look for cracks in the concrete radiating from the bolts, base plates that rock, or gaps under the posts. Any of those means stop and get it checked. If you are installing a new lift, our guide to concrete floor requirements explains what to check first.

A simple maintenance schedule

This is a typical good-practice routine for a lift in regular use. Use it as a starting point and change the intervals to match your manual and how hard the lift works:

When What to do
Before each day’s use Visual check, leaks, locks click, arms and pads, floor clear
Weekly in a busy workshop, monthly at home Clean and lubricate chains, pulleys, lock pawls and arm pins; check cables and synchronisation
Monthly Hydraulic oil level with the lift fully down, hoses and fittings, rubber pads
Every few months Anchor bolts and base plates, cracks in the concrete, electrical leads and controls
Yearly, or as the manual says Full inspection by a competent person, hydraulic oil change if the manual calls for it, worn parts replaced

Keep a notebook or a sheet on the wall and write down each check, the date and anything you found. In a workshop that log is part of your safety records. For the daily part, use the printable sheet in our car lift safety checklist.

Scissor lifts and portable lifts

  • Clean and lubricate the scissor pivot pins and rollers. Grit in the pivots wears them fast.
  • Check hydraulic hoses where they bend as the lift opens and closes.
  • Test the mechanical lock every time, and use it every time you work underneath.
  • On the portable 2700kg lift, check the hose and lead are not crushed when you move the lift, and keep the wheels free of grit.

Warning signs: stop and call

  • Carriages or runways rising unevenly, or the car tilting.
  • Locks that do not click in on one post, or need a push to engage.
  • Jerky movement, new noises from the power unit, or the lift slowing down.
  • Oil on the floor, on the posts or around the cylinders.
  • A frayed cable, a stiff or rusted chain, or a cracked weld.
  • The lift sinking while held on the hydraulics.

Do not use a lift showing any of these. We repair and service lifts and supply spare parts, and every lift we sell carries an 18-month parts warranty. Call us with the model and what you are seeing. When you buy from us with installation, our engineers show you the routine for your model at handover.

Maintenance on the other equipment in the bay

The same habits apply to the rest of the workshop. Our fully automatic tyre changer needs its oil level checked, the machine kept clean and moving parts lubricated at least once a month. Our 3000kg low profile trolley jack needs its hydraulic fluid changed every three years. Ten minutes a month keeps all of it working.

Thinking of a used lift instead of a new one? Maintenance history is the first thing to ask for: see second hand vs new car lift. Or browse our car lifts.

Paying for it: buy online with card, Apple Pay, Shop Pay or Klarna (pay in 3 interest-free payments or spread the cost), or order by phone or WhatsApp and pay the driver on delivery by card, bank transfer or cash. See payment terms.

Lifts in this guide: 4000kg 2 Post Lift (£1,700 delivered) · 6 Ton 2 Post Lift, chain drive (£2,800) · 4000kg 4 Post Lift (£2,800) · Full Rise 3500kg Scissor Lift (£2,700)

Questions and answers

How often should a car lift be serviced?

Check it before each day’s use, lubricate and check it regularly as the manual says, and have it inspected by a competent person at least yearly, more often in a busy workshop. The manual for your model gives the intervals.

What oil goes in a car lift?

Hydraulic oil of the grade stated in your lift’s manual. Do not mix types. If you are unsure what is in your lift, ask the supplier before topping up.

How do you lubricate car lift chains?

Clean off grit and old lubricant, then apply the chain lubricant named in the manual so it gets between the links. Run the lift up and down to work it in.

Why is my car lift going down slowly on its own?

A lift that sinks on the hydraulics usually has a seal or valve problem. Stop using it, keep everyone from under it, and get it checked.

How do I check the safety locks on a car lift?

Raise the empty lift and listen for an even click on every post. Clean and lubricate the pawls, check the springs, and make sure all locks engage and release together.

Not sure which lift fits? Call us on 020 8220 9986 or message us on WhatsApp 07811 247454, every day 9am to 9pm. Send your ceiling height, floor and the cars you work on, and we will tell you which lift fits.


Get a price for your garage

Leave your number and postcode. We call you back with a delivered or installed price and check the lift fits your ceiling and floor. Every day 9am to 9pm.

Delivered and installed by our own team. Pay online, with Klarna or on delivery. We only use your details to answer this request.